kalle123
User
Doro, das ist die config der Testschaltung vom Bild
Auch ELRS
und ich sehe bei deiner config auch nichts Ungewöhnliches.
ELRS settings im Sender sind OK? RX/TX zwischen ELRS Empfänger und RP2040 (pin 5 (sollte TX sein) und pin1 (sollte RX sein)
Die Schrift auf den kleinen Schei... Dingern. Brauch da inzwischen eine Lupe
Kalle
Auch ELRS
Code:
processing cmd
Version = 2.13.6
Function GPIO Change entering XXX=yyy (yyy=255 to disable)
Primary channels input = 9 (PRI = 5, 9, 21, 25)
Secondary channels input = 255 (SEC = 1, 13, 17, 29)
Telemetry . . . . . . . . = 10 (TLM = 0, 1, 2, ..., 29)
GPS Rx . . . . . . . . . = 11 (GPS_RX = 0, 1, 2, ..., 29)
GPS Tx . . . . . . . . . = 12 (GPS_TX = 0, 1, 2, ..., 29)
Sbus OUT . . . . . . . . = 255 (SBUS_OUT= 0, 1, 2, ..., 29)
RPM . . . . . . . . . . = 255 (RPM = 0, 1, 2, ..., 29)
SDA (I2C sensors) . . . . = 14 (SDA = 2, 6, 10, 14, 18, 22, 26)
SCL (I2C sensors) . . . . = 15 (SCL = 3, 7, 11, 15, 19, 23, 27)
PWM Channels 1, 2, 3 ,4 = 0 1 2 3 (C1 / C16= 0, 1, 2, ..., 15)
PWM Channels 5, 6, 7 ,8 = 255 255 255 255
PWM Channels 9,10,11,12 = 255 255 255 255
PWM Channels 13,14,15,16 = 255 255 255 255
Voltage 1, 2, 3, 4 = 255 255 255 255 (V1 / V4 = 26, 27, 28, 29)
RGB led . . . . . . . . . = 16 (RGB = 0, 1, 2, ..., 29)
Logger . . . . . . . . . = 255 (LOG = 0, 1, 2, ..., 29)
ESC . . . . . . . . . . . = 255 (ESC_PIN= 0, 1, 2, ..., 29)
Locator CS . . . . . . . = 255 (SPI_CS = 0, 1, 2, ..., 29)
SCK . . . . . . . = 255 (SPI_SCK= 10, 14, 26)
MOSI . . . . . . = 255 (SPI_MOSI=11, 15, 27)
MISO . . . . . . = 255 (SPI_MISO=8, 12, 24, 28)
Output level High . . . . = 255 (HIGH = 0, 1, 2, ..., 29)
Output level Low . . . . = 255 (LOW = 0, 1, 2, ..., 29)
Esc type is not defined
Protocol is CRSF (=ELRS)
CRSF baudrate = 420000
Logger baudrate = 115200
PWM is generated at = 50 Hz
Voltage parameters:
Scales : 1.000000 , 1.000000 , 1.000000 , 1.000000
Offsets: 0.000000 , 0.000000 , 0.000000 , 0.000000
No temperature sensors are connected on V3 and V4
RPM multiplier = 1.000000
Baro sensor is detected using BMP280 at I2c adress 76
Sensitivity min = 100 (at 100) , max = 300 (at 1000)
Hysteresis = 5
Airspeed sensor is not detected
No Vspeed compensation channel defined; oXs uses default settings
First analog to digital sensor is not detected
Second analog to digital sensor is not detected
Foreseen GPS type is Ublox (configured by oXs) :GPS is detected but has not (yet) a fix
Led color is normal (not inverted)
Failsafe type is HOLD
Acc/Gyro is detected using MP6050
Acceleration param: ACC= 0.000000 0.000000 0.000000
1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
Gyro offsets X, Y, Z = 0 , 0 , 0
Orientation Horizontal is UP(Z+) Vertical is FRONT(X+)
Gyro is not configured
No sequencers are defined
Config parameters are OK
Press ? + Enter to get help about the commands
und ich sehe bei deiner config auch nichts Ungewöhnliches.
ELRS settings im Sender sind OK? RX/TX zwischen ELRS Empfänger und RP2040 (pin 5 (sollte TX sein) und pin1 (sollte RX sein)
Die Schrift auf den kleinen Schei... Dingern. Brauch da inzwischen eine Lupe
Kalle